Water butt leak

  • 4 Replies
  • 310 Views
*

DFCskip

  • Newbie
  • *
  • Location: Dartford, Kent, UK
  • 3
Water butt leak
« on: July 08, 2020, 18:24 »
Hi,

Has anyone successfully repaired a water butt with a small hole in the base? Id really appreciate any repair tips.

Many thanks

*

JayG

  • Global Moderator
  • Hero Member
  • *****
  • Location: South West Sheffield
  • 16085
Re: Water butt leak
« Reply #1 on: July 09, 2020, 08:23 »
Yes, more than once (different leaks, although I had to re-do one I didn't get right first time.)

I used an electric soldering iron to melt the edges of the rupture back together, with a thin slice of plastic taken from the lip of the lid as 'solder'. Anything larger than a miniature soldering iron (mine is 15W) would probably be too hot and unwieldy to control.

Sounds fiddly, and it is, but I couldn't find a reasonably priced glue or solvent which would have done the job on plastic exposed to water and the elements.

Check it wasn't the stand causing the rupture - at least two of the punctures in mine were the result of the 'claws' of the stand compressing the corners of the butts (I cut them off with a hacksaw!)
Sow your seeds, plant your plants. What's the difference? A couple of weeks or more when answering possible queries!

One of the best things about being an orang-utan is the fact that you don't lose your good looks as you get older

*

rowlandwells

  • Hero Member
  • *****
  • Location: northamptonshire
  • 1812
Re: Water butt leak
« Reply #2 on: July 09, 2020, 08:58 »
i must say i agree with what Mum has said although you haven't said if it was metal or plastic if its metal and easy to get at I've repaired those leaks by drilling a small hole where the leak is then using a bolt and 2 washer to cover the hole with some plumbers mate between the washer and the but  and then using the other washer and nut tighten up sealing the leak that works fine or has done for me

as for a plastic mend you could do the same or  as said use a solvent i bought some from Halfords that to has done the job ok

*

lettice

  • Hero Member
  • *****
  • Location: Sunny South Coast, Hampshire
  • 1336
Re: Water butt leak
« Reply #3 on: July 10, 2020, 09:28 »
As above depends on whether its metal or plastic.
I have mended a few watering cans with leaks.
A metal one I had was leaking from the bottom. I coated the inside base with bitumen paint and it has not leaked now for ten years.
I also have an old plastic one that had a poor screw type seal all around the bottom edge, but over the years it began to leak. It had this seal so you could remove the base and clean the inside of the can. I used Gorilla tape - Black on that, just a single layer all around the inside seal edge of the can and it has not leaked in its five years.
That can often sits for long periods with water inside it, as its wide top opening catches rainwater easily too.

*

jezza

  • Senior Member
  • ****
  • 836
Re: Water butt leak
« Reply #4 on: July 18, 2020, 22:33 »
Hello I found a hot air paint stripper warms the plastic enough to run a knife down the split,hold the knife blade edge to the split then warm plastic and knife together ,had to do a barrel a month ago it got shot and when a piece of lead comes out I find the hole with a spout of water,  jezza



xx
Cheap water butts and water butt pumps

Started by ConfusedGardener on Equipment Shed

5 Replies
3856 Views
Last post May 07, 2013, 20:50
by ConfusedGardener
xx
Water Butt Offer from Yorkshire Water

Started by SweetPea on Equipment Shed

20 Replies
19228 Views
Last post July 21, 2006, 15:58
by Basil Fawlty
xx
Tap For Water butt

Started by pookey on Equipment Shed

3 Replies
2904 Views
Last post July 03, 2007, 05:18
by Gwiz
xx
Water Butt

Started by mrs bouquet on Equipment Shed

3 Replies
584 Views
Last post March 20, 2019, 19:33
by jaydig
 

Page created in 0.123 seconds with 41 queries.

Powered by SMFPacks Social Login Mod
Powered by SMFPacks SEO Pro Mod |