Merry Tiller Carburetor Linkage

  • 5 Replies
  • 329 Views
*

Stuart Wheeler

  • Newbie
  • *
  • 3
Merry Tiller Carburetor Linkage
« on: May 31, 2020, 20:03 »
Hi All

I have a Type D Merry Tiller that I am trying to get working again but what is stopping me is not knowing how the throttle, governor linkage is set up and what parts of the linkage are actually missing. Looking at the parts diagram doesn't really help. Has anyone got a photo of the setup with a Briggs jet-flo carb?
carb.jpg

*

jezza

  • Senior Member
  • ****
  • 894
Re: Merry Tiller Carburetor Linkage
« Reply #1 on: June 01, 2020, 18:44 »
Hello try R Tellertine on this site he's a Merrytiller expert , I know abit about Briggs engines but haven't seen that type of governor on this engine before I've seen a similar set up on a Mag engine  jezza

*

Stuart Wheeler

  • Newbie
  • *
  • 3
Re: Merry Tiller Carburetor Linkage
« Reply #2 on: June 01, 2020, 21:34 »
Thanks for the tip. Just have to work out how to contact him.

*

R Tallentire

  • Experienced Member
  • ***
  • Location: Lancaster
  • 198
Re: Merry Tiller Carburetor Linkage
« Reply #3 on: June 01, 2020, 21:55 »
You already have, the flo-jet carb mechanism is unusual. I will put up a couple of pics from the B & S workshop manual, but the one showing the top of the L shaped rod is for the fixed speed (generator) engine. for those with throttle cables the top (compression) spring is longer and lighter, and the knurled nut isn't knurled, but has a split pin through it and the rod. The split pin holds the top of this spring in place.
B&S linkage.jpg
Throttle cable.jpg
R Tallentire

*

Stuart Wheeler

  • Newbie
  • *
  • 3
Re: Merry Tiller Carburetor Linkage
« Reply #4 on: June 01, 2020, 22:00 »
That is absolutely super. Been looking for a diagram like this for ages. It looks as if I am just missing the knurled nut and the clip that the rod passes through but I should be able to create something to do the job.
Thanks a lot.

*

R Tallentire

  • Experienced Member
  • ***
  • Location: Lancaster
  • 198
Re: Merry Tiller Carburetor Linkage
« Reply #5 on: June 02, 2020, 21:10 »
As I wrote, it isn't a knurled nut on Merry Tillers, in fact it isn't much like a nut at all, a piece of aluminium tube threaded inside. If I remember rightly it just limits how far down the rod can be pulled by the cable, the spring goes over it and is held by the spit pin and a flat washer at the top.



xx
merry tiller and mantis tiller - compare/contrast?

Started by mushroom on Equipment Shed

7 Replies
7191 Views
Last post July 17, 2007, 05:17
by Gwiz
xx
Merry Tiller Help

Started by John on Equipment Shed

4 Replies
8828 Views
Last post February 04, 2006, 20:48
by John
xx
merry tiller need help

Started by madmak on Equipment Shed

3 Replies
1253 Views
Last post March 27, 2010, 19:17
by jarigo
clip
Merry Tiller

Started by glenforkie on Equipment Shed

11 Replies
5962 Views
Last post February 26, 2014, 15:57
by Swed
 

Page created in 0.103 seconds with 41 queries.

Powered by SMFPacks Social Login Mod
Powered by SMFPacks SEO Pro Mod |